Finger Splice

• Die Cut Fingers Provide Increased Area For Fusing Resulting In A Stronger Splice Than Butt Splices
• In thicker materials it is possible to eliminate Reinforcement Material
• Excellent Release Surface

Butt Slice With Reinforcement

• Requires Sealed Reinforcement Top Or Bottom
• High Temp Applications May Require Sewn Reinforcement On Splice And Edges
• Minimal Marking Of Product

Heat Seal es Overlap Splice

• Belt Ends Overlapped from 1/2 to 2 Inches and Then Heat Sealed
• Standard Splice For Most Applications
• Can Be Sewn For Extra Strength

Scarf Splice

• 1 Inch Long Skive on Both Ends And Joined
• Eliminates Bump At Seam

Clipper® Lace with "Bullnose" Reinforcement For Mounting -Overview

• Individual Wire Hooks With Connecting Pin Forming Hinge

K2SP (Biscor Code) Clipper

• Wire Dia: 0.62mm
  Pitch: 1.70mm (59hooks/100mm)
  Produces a flat unobtrusive splice generally used on belts up to 1500mm wide
  
• Temperature rating: - 50° to + 260°C
• Stainless Steel Or Galvanized Steel
• Greater Cross Section Of Wire And Should Be Stronger Than K4SP

K4SP (Biscor Code) Clipper

• Wire Dia: 0.80mm
  Pitch: 2.54mm (40hooks/100mm)
  
• Temperature rating: - 50°C to + 260°C
• Stainless Steel Only
• Wider Distance Between Wires Than K2SP (Easier Installation)

SW001 (Biscor Code)

• Wire Dia: 1mm
  Pitch: 3.175mm (32hooks/100mm)
  
• Temperature rating: - 50°C to + 260°C
• similar to the K2SP and K2SP except that the hooks are held together by a welded wire, which remains attached after installation

Allegator® Lace with "Bullnose" Reinforcement For Mounting - Overview

• Produced From Continuous Strip Of Metal
• Less Chance Of Metal Breaking Off Into Product
• Disadvantage Is That Damage On Edge Can Work Rest Of Lace Loose
• Installation Damage To Bullnose From Metal Lacing Can Cause Premature Belt Failure
• Generally Use In Food Applications Over Wire Hook Clipper® Lace

G001 Allegator Lace

G003 Alligator Lace

Metal Inox Spiral Splice

• Wire Dia: 0.70mm
  Stainless Steel spiral woven into Kevlar® mesh material produces a flat, flexible and breathable splice.
  
• Temperature rating: - 50°C to + 260°C

SS 'Soft Seal' or Castellated Splice - overview

• 6mm teeth are die-cut into the belt ends, typically constructed with Teflon® Coated woven Kevlar®.
• Temperature rating: - 50°C to + 260°C
• "Soft Seal" Indicates Not Metal

Soft Seal Splice - close up

• 6mm teeth are die-cut into the belt ends, typically constructed with Teflon® Coated woven Kevlar®.
• Temperature rating: - 50°C to + 260°C
• "Soft Seal" Indicates Not Metal

PEEK® spiral - Overview

• Easy To Install High Temperature Plastic Spiral Lacing
• Allows Air Flow Throughout Splice

peek® spiral - Close Up

• Monofilament Dia: 0.90mm Peek®
• Temperature rating: - 50°C to + 180°C

Polyester Spiral

• Spiral R/W
  Wire Dia: 0.90mm
  
• Temperature rating: - 50°C to + 150°C
  
• For installation on Bisca-Pol belts
  

Nomex® Hook

• Wire dia: 2 X 0.90mm dia yarns
  
• Temperature rating: - 50°C to + 180°C
  
• Abuse resistant